ࡱ> z}y ALbjbj>> }zTT/D $***Pz<|*[P22222   OOOOOOO$!RTP     P22P r22O O^B N2?xX^6L*O+P0[P`L"sUsUTNsUND       PP   [P    sU          : PROTEK SYSTEMS, INC. Architectural Specification CSI/CSC SectionFormat [3-part] CSI PageFormat ProTek Systems, Inc. 1250 Wallace Dr. Unit B, Delray Beach, FL 33444 USA Toll Free: 800.598.2153 Fax: 561.395.4771 e-mail: projects@protekmail.com www.proteksystem.com This is a manufacturer specific proprietary product specification using the proprietary method of specifying applicable to project specifications and master guide specifications. Specifier should edit guide specifications in accordance with project requirements. Add or modify text as required. Specifier Notes typically precede specification text: delete notes in final version of specification. Revise below to suit project requirements, specification practices and section content. Refer to CSI/CSC MasterFormat for other section numbers and titles. The specifier is responsible for the accuracy of all project specifications, including any ProTek guide specifications used. The designer/specifier is responsible for product selection as well as the use and application of this information, and should contact the manufacturer to ensure that models, types, finishes, etc. are available and that the associated specification information is valid and correct. ProTek shall not be liable for any damages arising out of the use of its guide specifications. SECTION 097700 SPECIAL WALL SURFACING PART 1 GENERAL ****************************************************************************************************** Specifier Note: List significant generic types of products, work or requirements ****************************************************************************************************** 1.01 SECTION INCLUDES A. This section includes: Interlocking wall panels with smooth finishes. Mounting hardware, adhesives, accessories and trims. B. Conform with requirements of all Sections of Division 1, General Requirements, as it applies to the work of this Section. 1.02 RELATED SECTIONS ****************************************************************************************************** Specifier Note: List statements that draw the readers attention to other specification sections dealing with work directly related to this section. ****************************************************************************************************** Division 06 Section: Rough and Finish Carpentry Division 09 Section: Gypsum Board Assemblies ****************************************************************************************************** Specifier Note: Article below may be omitted when specifying manufacturers proprietary products and recommended installation. Retain Reference Article when specifying products and installation by an industry reference standard. If retained, list standard(s) referenced in this section. Indicate issuing authority name, acronym, standard designation and title. Establish policy for indicating edition date of standard referenced. Conditions of the Contract or Division 1 References Section may establish the edition date of standards. This Article does not require compliance with standard, but is merely a listing of references used. Article below should list only those industry standards referenced in this section. ****************************************************************************************************** 1.03 REFERENCES General: Standards listed by reference, including revisions by issuing authority, form a part of this specification section to extent indicated. Standards listed are identified by issuing authority, authority abbreviation, designation number, title or other designation established by issuing authority. Standards subsequently referenced herein are referred to by issuing authority abbreviation and standard designation. American Society for Testing Materials (ASTM): ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials. ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics. ASTM D638 Standard Test Method for Tensile Properties of Plastics. ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials. ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor. 1.04 SYSTEM DESCRIPTION A. Performance Requirements: Provide interlocking wall panels which have been manufactured and installed to maintain performance criteria stated by manufacturer without defects, damage or failure. 1.05 SUBMITTALS ****************************************************************************************************** Specifier Note: Include requests for relevant data to be furnished by the contractor, before during or after construction. ****************************************************************************************************** A. Product Data: Submit manufacturers current printed product literature, specifications, installation instructions, and field reports in accordance with Section 01330 - Submittal Procedures. B. Shop Drawings: Submit shop drawings to indicate materials, details, and accessories in accordance with Section 01330 C. Samples: Submit duplicate sample pieces of material, as well as accessory pieces in accordance with Section 01330 - Submittal Procedures. D. Quality Assurance Submittals: Submit the following: 1. Manufacturers Instructions: Current published manufacturers installation and maintenance instructions. E. Closeout Submittals: Submit the following: 1. Operation and Maintenance Data: Operation and maintenance data for installed products in accordance with Division 1 Closeout Submittals (Maintenance Data and Operation Data) Section. Include methods for maintaining installed products and precautions against cleaning materials and methods detrimental to finishes and performance. 2. Warranty: Warranty documents specified herein. ****************************************************************************************************** Specifier Note: This Article should include standards, limitations and criteria which establish an overall level of quality for products and workmanship for this section. Coordinate with Section 01430 - Quality Assurance. ****************************************************************************************************** 1.06 QUALITY ASSURANCE A. Installer Qualifications: Installer experienced in performing work of this section who has specialized in installation of work similar to that required for this project. ****************************************************************************************************** Specifier Note: Describe requirements for meetings to coordinate materials and techniques, and to sequence related work. ****************************************************************************************************** B. Pre-installation Meeting: Conduct pre-installation meeting to verify project requirements, substrate conditions, manufacturers installation instructions and manufacturers warranty requirements. ****************************************************************************************************** Specifier Note: This Article should include special and unique requirements. Coordinate with Sections 01650 - Product Delivery Requirements or Section 01660 - Product Storage and Handling Requirements. ****************************************************************************************************** 1.07 DELIVERY, STORAGE & HANDLING A. Ordering: Comply with manufacturers ordering instructions and lead time requirements to avoid construction delays. B. Deliver, store and handle materials in accordance with Section 01610 - Basic Material Requirements. C. Deliver materials in manufacturers original, unopened, undamaged containers with identification labels intact. D. Store materials protected from exposure to harmful weather conditions, at temperature and humidity conditions recommended by manufacturer. E. Store panels in temperature controlled environments. 1.08 WASTE MANAGEMENT AND DISPOSAL ****************************************************************************************************** Specifier Note: Include information that will assist the contractor in dealing with the disposal of construction waste materials in ways other than using landfill resources. ****************************************************************************************************** A. Deposit all packaging materials in appropriate container on site for recycling or reuse. B. Avoid using landfill waste disposal procedures when recycling facilities are available. C. Keep all discarded packaging away from children. 1.09 PROJECT CONDITIONS A. Maintain air temperature and structural base temperature at installation area between 60F (16C) and 75F (24C) for 48 hours before, during and 24 hours after installation. ****************************************************************************************************** Specifier Note: Coordinate Article below with Conditions of the Contract and with Division 1 Closeout Submittals (Warranty) Section. ****************************************************************************************************** 1.10 WARRANTY A. Project Warranty: Refer to Conditions of the Contract for project warranty provisions. B. Manufacturers Warranty: Submit, for Owners acceptance, manufacturers standard warranty document executed by authorized company official. Manufacturers warranty is in addition to, and not a limitation of, other rights Owner may have under Contract Documents. PART 2 PRODUCTS 2.01 MANUFACTURERS Manufacturer: ProTek Systems, Inc. 1. 1250 Wallace Dr. Unit B, Delray Beach, FL 33444 Toll-free: 800.598.2153 Fax: 561.395.4771 2. E-mail: projects@protekmail.com Web Site: www.proteksystem.com. 2.02 COMPOSITE WALL & CELING PANELS ************************************************************************************************** Specifier Note: Select material to suit project requirements. ************************************************************************************************** WCUL-400 Interlocking Wall Panels by ProTek Systems, Inc. Material: 0.400 Corrugated polypropylene substrate with a smooth finish and tongue-and-groove edge Stock Widths: 16 or 24 planks. Stock Lengths: 8ft, 10ft, 12ft, 16ft, or 20ft. Color: White. Fire Rating Class: A. Flexural Strength (ASTM D790): 2,233 lbf/in2. Flexural Modulus (ASTM D790): 156,976 psi. Tensile Strength (ASTM D638): 1,308 psi. Barcol Hardness (ASTM D2583): -- Izod Impact (ASTM D256): 1.57 ft-lb/in. Surface Burning Characteristics (ASTM E84): Class A. 2.03 ACCESSORIES PVC Trim Moldings WCUL-400-TC-98 Top/End Cap WCUL-400-JC-99 Joint Cover WCUL-400-IC-100 Inside Corner WCUL-400-OC-101 Outside Corner B. Mounting Method: Adhesive OR mechanical fasteners. Adhesive: Provide panel adhesive as recommended by panel manufacturer. Mechanical fasteners: Provide appropriate fasteners and accessories as required to properly complete installation. 2.04 SOURCE QUALITY Source Quality: Obtain wall products from ProTek Systems, Inc. No substitutions. PART 3 EXECUTION 3.01 MANUFACTURERS INSTRUCTIONS A. Compliance: Comply with manufacturers product data and installation instructions. 3.02 EXAMINATION A. Site Verification of Conditions: Verify substrate conditions, which have been previously installed under other sections, are acceptable for product installation in accordance with manufacturers instructions. 3.03 SUBSTRATE PREPARATION Walls should be smooth and level. High points must be removed and low points filled with filler intended for the substrate and environmental conditions. Wall tiles must be fixed firmly to the wall. As long as the tile edges do not protrude you do not have to skim grout joints. Surfaces must be permanently dry and free from all substances that may contribute to adhesive bond failure. Remove loose paint and conduct an adhesive bond test with paint. Exterior walls must be adequately damp-proofed and insulated. Drywall substrates should be paint ready. 3.04 PREPARATION All surfaces must be free from dust and cleaned prior to installation. The working environment must also be dust free. Failure to comply with these conditions will reduce the bond strength between the adhesive and substrate, and may cause the panels to detach. Very absorbent / porous substrates (particularly plaster finishes and unprimed sheetrock) must have a proprietary sealer e.g. PVA primer or similar, applied to the surface a minimum of 12 hours prior to the installation. All electrical switches, power points etc., should be in a first fix / installation state. All electrical equipment should only be moved or altered by a qualified electrician. All plumbing should have pipe-work removed to a first fix or installation state and tails left protruding from the substrate. Panels can then be drilled and slid over the pipe tails. All holes should be drilled 1/8 (3mm) oversize, then sealed with caulking. Plumbing should always be done by a qualified plumber. Hot pipes and steam pipes should be insulated and a 1/8 to 1/4 (3-6mm) expansion gap should be created when installing panels around these pipes, then sealed with caulking. All pipes, fixing bolts, etc. extending through the panels should have a minimum 1/8 (3mm) expansion gap and be sealed with caulking. If fitting to door frames, these must be in place prior to installation of panels. Prior to installation, it is advisable to complete any painting which comes in contact with panels, as sealant used at junctions is non-paintable. Panels should be stored flat and be pre-conditioned a minimum of 24 hours in ambient temperatures similar to the prevailing operational conditions. The panels must be stored on a level flat surface off the ground (risk of condensation on the panels if stored on damp surfaces). Storage on uneven surfaces could cause the panels to distort prior to installation. First, check the rooms using a 6 (2 m) level to ensure all walls are flat, paying particular attention to the corners, window reveals, and door entrances. These need to be inspected to ensure they are free of any debris or irregularities, which could prevent the panels laying flat to the substrate after the adhesive has been applied and the panel installed. ****************************************************************************************************** Specifier Note: Coordinate Article below with manufacturers recommended installation details and requirements. ****************************************************************************************************** 3.05 INSTALLATION A. Interlocking Wall Panel Installation: Install WCUL-400 interlocking wall panel systems in accordance with the current published ProTek Installation Guide. Failure to install ProTek WCUL-400 interlocking wall panels in accordance with recommended procedures will void the ProTek Limited Product Warranty. ****************************************************************************************************** Specifier Note: Coordinate Article below with Division 1 Quality Assurance and Quality Control Sections. ****************************************************************************************************** 3.06 FIELD QUALITY REQUIREMENTS ****************************************************************************************************** Specifier Note: Coordinate paragraph below with Division 1 Quality Assurance Section and Part 1 Quality Assurance Submittals herein. ****************************************************************************************************** A. Manufacturers Services: Upon Owners request, provide manufacturers service consisting of product use recommendations and product installation recommendations in accordance with manufacturers instructions. 3.07 CLEANING ****************************************************************************************************** Specifier Note: Once all panels are installed, clean all surfaces down with antistatic solution or antistatic wipes. This is required as the panel may have static build up and any dust in the atmosphere will adhere to the surface of the panel. ****************************************************************************************************** Clean panel surfaces in compliance with manufacturers recommendations. Use a clean, damp, nonabrasive cotton cloth and a mild liquid detergent or household cleaner. Rinse with clean water using a clean, nonabrasive cotton cloth. Dry panels with a soft, clean nonabrasive cotton cloth. Do not use cleaners containing acid, alkali, or sodium hypochlorite. ****************************************************************************************************** Specifier Note: If a construction waste separation and disposal work plan is incorporated as part of the project, ensure that this section makes reference to how the excess material can be recycled or otherwise disposed of. Avoid sending construction waste to landfill sites if alternative means of disposal are available. ****************************************************************************************************** B. Remove construction debris from project site and legally dispose of debris. END OF SECTION     0`auv  6 l > B D E [ ] l ľӺӺӺӯ떍}yuyh`5h hMCJhVbhVb5CJhVbhVbCJh&]h#ZPCJhM0J>*B*OJQJphhmh B*phhM h20J hM0Jhfh20J hfh2h2h3"h&]h#ZP0J h&]h#ZPh&]h#ZP5 hM5.1P`av  4 5 E   $1$a$gdM1$gd  $1$a$gd2$$$a$$a$E \ ] m n #$ Mz{ & F1$gd `0^`0 0^`0 & F `0^`0$a$ %&!" 0LMyzXY-PFUCb)*- "0"##0$@$&#&q''',(<(L*𿻴hE|hg)h hVbhVb h&]h)h)h8HhVb h&]h%uL h h h9yh%uL h&]h h#ZPh`5h h&]h#ZPh&]h#ZP5={)*Y & F pgd  & F pp0^p`0gd  p^pgd9y$$ & F `gd%uL$$ & F `0^`0gd%uL$$ & F `0^`0gd%uL$$F()cd)* `p0^p`0gdVb  & F `^ & F `0^`0gdVb & F `0^`0EF ! !!! ""####0$$a%b% & F `0^`0 `p0^p`0 & F `^`b%%%%%d&e&&&g'h''''',((A)B)))))/*0* `0^`0 0^`0 & F `0^`00*H*I***_++K,L,Z,[,,,------ . & F & F `0^`0 $0^`0$$ & F `0^`0$$gdA & F `0^`0gdg)L********_+o+++L,-----. . .;.L.T.Z.f.g.j.r.........3/B//// 00+0r0s0❔~w hRRhRRhRRh\ah^h&]h#ZP5^Jh&]h#ZP^J h&]h$'-hUhAQJaJhAhAQJaJ h&]h& hhThY h&M9h& hAh h&]hAh#ZPh&]h#ZP5 h&]h#ZPh hg)hg). .g.....3/q//00s000001@1i1  & F gdSl & F @ 0^@ `0gdRR & F 0^`0gd\a  & F gdSl gd gdA p0^p`0gd& s0000011?1@1h1i1111111111 222222222223p3q3r333333333G4L4e4g4h4y4z4V5]5k5666r7u77777殧ή֮ h&]h] h]h]h]h]h#ZPCJh&]h#ZP5hb($ h&]h&h#ZPhe!h&hp!hh\a h&]h#ZPhL- hSlhSlhSlhRR=i1111111 2 2(2C2a2222  & F@& `gdSl & Fp0@& ^p`0gd\a  & F@& `gdSl & Fp0@& ^p`0gdSl  & F@& gdSl$$$$ `0^`0  & F@& gdp!  & F gdSl222r3s33333333344g4 & F `0^`0$$$ ^`gd& & F gd& 0^`0 & F `@ 0^@ `0gd& & F `@ 0^@ `0gde! & F `0^`0g4h4y4z4N5O5j5k56666662737q7r7777  & F `gd] & F `^gd] `gd] & F `0^`0 `0^`0`gd]778899D:E:;;1<2<<< ====8>9>??y@z@@ & F0@& ^`0 & Fgd]$a$gd] & Fgd]778&88888H9I999E::::'<0<1<2<f<s<<<<= = ==P=j=p===9>A>!?U?y@@@PAQAAAAAAAABBBBB%BOBUBjB}BBBBhb($hx[hah/h#ZPCJaJh&]h#ZP5 h&]h#ZPh hU@hah/h]@hEh]^J hEh] h'"h] h]^Jh]B*phh]hU>@QAAAAABCChCC8D9DYDZDDEEFFFFFG1$gdx[ & F `0^`0gd_a 0^`0 & F `0^`0BBBBBBBBhCxCDDEEBFRFF GG(GGGUHHHHHI!J0JfJgJKKKL,L-L/L0L2L3L5L6L8L9L;LL?Lμh/ch$'-h$'-B*CJphh=]jh=]Uh#ZP h#ZP0Jh&]h#ZP0J hhhx[hah/h#ZP@hah/hah/@hah/hx[@hah/h#ZP5@h_ah&]h#ZP5 h&]h#ZPhb($hUh2GTHUHHHHL?L@LAL$a$gd$'- ?L@LALh#ZPh=]90PBP/ =!&"&#$% Dp@ 00P@P BP/ =!&"&#$% Dp^! 2 0@P`p2( 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p 0@P`p8XV~_HmH nH sH tH P`P Normal1$7$8$H$CJOJQJ_HmH sH tH \@\  Heading 2$<@& 56CJOJQJ\]^JaJDA D Default Paragraph FontViV  Table Normal :V 44 la (k (No List <& < Footnote ReferenceV>@V Title$<@&a$5CJ KHOJQJ\^JaJ 0o0 SpecTextSectFU`!F Hyperlink>*B*CJOJQJaJphDO2D Level 1 & F0@&^`0DOBD Level 2 & F0@&^`0DORD Level 3 & Fp0@&^p`0./a. SPECText[4]8B@r8 Body Text$a$CJPR@P Body Text Indent 2p0^p`0FV`F FollowedHyperlink >*B* phTC@T Body Text Indentp01$^p`0aJ:@: s Footnote TextCJ44 $'-Header  !4 @4 $'-Footer  !H@H %uL Balloon TextCJOJQJ^JaJNoN %uLBalloon Text CharCJOJQJ^JaJ@@@ %uL List Paragraph ^PK![Content_Types].xmlN0EH-J@%ǎǢ|ș$زULTB l,3;rØJB+$G]7O٭V$ !)O^rC$y@/yH*񄴽)޵߻UDb`}"qۋJחX^)I`nEp)liV[]1M<OP6r=zgbIguSebORD۫qu gZo~ٺlAplxpT0+[}`jzAV2Fi@qv֬5\|ʜ̭NleXdsjcs7f W+Ն7`g ȘJj|h(KD- dXiJ؇(x$( :;˹! I_TS 1?E??ZBΪmU/?~xY'y5g&΋/ɋ>GMGeD3Vq%'#q$8K)fw9:ĵ x}rxwr:\TZaG*y8IjbRc|XŻǿI u3KGnD1NIBs RuK>V.EL+M2#'fi ~V vl{u8zH *:(W☕ ~JTe\O*tHGHY}KNP*ݾ˦TѼ9/#A7qZ$*c?qUnwN%Oi4 =3N)cbJ uV4(Tn 7_?m-ٛ{UBwznʜ"Z xJZp; {/<P;,)''KQk5qpN8KGbe Sd̛\17 pa>SR! 3K4'+rzQ TTIIvt]Kc⫲K#v5+|D~O@%\w_nN[L9KqgVhn R!y+Un;*&/HrT >>\ t=.Tġ S; Z~!P9giCڧ!# B,;X=ۻ,I2UWV9$lk=Aj;{AP79|s*Y;̠[MCۿhf]o{oY=1kyVV5E8Vk+֜\80X4D)!!?*|fv u"xA@T_q64)kڬuV7 t '%;i9s9x,ڎ-45xd8?ǘd/Y|t &LILJ`& -Gt/PK! ѐ'theme/theme/_rels/themeManager.xml.relsM 0wooӺ&݈Э5 6?$Q ,.aic21h:qm@RN;d`o7gK(M&$R(.1r'JЊT8V"AȻHu}|$b{P8g/]QAsم(#L[PK-![Content_Types].xmlPK-!֧6 0_rels/.relsPK-!kytheme/theme/themeManager.xmlPK-!0C)theme/theme/theme1.xmlPK-! ѐ' theme/theme/_rels/themeManager.xml.relsPK] 5ADz;z  L*s07B?LAL'*0279<E {b%0* .i12g47@G7LAL()+,-./134568:;8@0(  B S  ?9Fag6?_#h#%%6&;&3'<''' ))i)o)))++88O:U:}::::h;q;!B*B/D1D2D4D5D7D8D:D;D?DBD"))++/D1D2D4D5D7D8D:D;D?DBD33333v &;&**@ACC.D/D1D2D4D5D7D8D:D;D?DBDv &;&**@ACC.D/D/D1D2D2D4D5D7D8D:D;D?DBD%S i@D )*X`rq-BQ΁01R,\e 2w'B>HG\(iT T@ALHZ * 6e!pheRGв        "tY                ~d        KJ\a8HSlz 23"d`A^e!p!b($)'$'-L-y-O.ah/n4`5CLFqH7LL%uL{`O#ZP{QbVQXx[&]=]_a/cA%e6*jEsnu/xZx9yjs}0Mo& [ RR)Vb]E|6gnTH%!&^8K3"sUP,[Yg)/D1D@;&;&;&;&AD@UnknownG*Ax Times New Roman5Symbol3. *Cx ArialQTCNMTimes New RomanE. Century Gothic5. .[`)TahomaA$BCambria Math"A h"gLr3RG- : "{- : "{! xx2 D D 3Q XR? &&]2!xx PROTEK SYSTEMS, INC. SPECANDREW AUKSTIKALNISFederico ChalasT             Oh+'0 $ D P \ ht|PROTEK SYSTEMS, INC. SPECANDREW AUKSTIKALNISNormalFederico Chalas4Microsoft Office Word@F#@t@P@tX^ - :՜.+,0 hp  Hewlett-Packard Company{" D PROTEK SYSTEMS, INC. SPEC Title  !"#$%&'()*+,-./0123456789:;<=?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghjklmnoprstuvwx{|Root Entry FӚxX^~1Table>UWordDocument }zSummaryInformation(iDocumentSummaryInformation8qMsoDataStoreP\xX^?xX^ZHDUOVWIGIL==2P\xX^?xX^Item PropertiesUCompObj r   F Microsoft Word 97-2003 Document MSWordDocWord.Document.89q